Illustrated Catalogue of Cotton Machinery - novelonlinefull.com
You’re read light novel Illustrated Catalogue of Cotton Machinery Part 17 online at NovelOnlineFull.com. Please use the follow button to get notification about the latest chapter next time when you visit NovelOnlineFull.com. Use F11 button to read novel in full-screen(PC only). Drop by anytime you want to read free – fast – latest novel. It’s great if you could leave a comment, share your opinion about the new chapters, new novel with others on the internet. We’ll do our best to bring you the finest, latest novel everyday. Enjoy
FRONT ROLL, 1 IN. DIA.
[Ill.u.s.tration]
Allowance has been made for doffing, etc. Filling Twist used, 3.25 x square root of number of yarn.
{160}
[Ill.u.s.tration]
HEAD END GEARING RING SPINNING FRAME
{161}
[Ill.u.s.tration]
SECTIONAL VIEW RING SPINNING FRAME
{162}
[Ill.u.s.tration]
SIDE VIEW RING SPINNING FRAME
{163}
SPINNING FRAME.
ALPHABETICAL REFERENCES TO DRAWINGS.
A Driving Pulley, 8 in. to 18 in. dia., advancing by 1/2 in. increments; 3-1/4 in. face.
A1 Cylinder Gear, 17, 21, 29 and 39 T.
A2 Cylinder, 7 in. dia.
B Jack Gear, 72, 76, 86, 96 and 106 T.
B1 Twist Change Gear, 25-67 T., advancing by one tooth.
C Intermediate Gear, 156 T. for 36-in. frame; 171 T. for 39 in. frame.
C1 Builder Motion Driving Sprocket Gear, 8 T.
D Front Roll Twist Gear, 84 T.
D1 Front Roll Draft Gear, 21 and 27 T.
D2 Front Roll, usually 1 in. dia.; sometimes 1-1/16 in. dia. and 1-7/8 in. dia.
E Crown Gear, 72, 90 and 108 T.
E1 Draft Change Gear, 32-59 T., advancing by one tooth.
F Large Back Roll Gear, 79 and 89 T.
F1 Small Back Roll Gear, 28 T. for 7/8 in. dia.
Middle and Back Rolls, 29 T. for 15/16 in. dia.
Middle Roll, 1-1/16 in. dia. Back Rolls.
F2 Back Roll, usually 7/8 in. dia., sometimes 11/16 in. dia.
and 1-1/8 in. dia.
G Broad Middle Roll Intermediate Gear, 48 T.
H Middle Roll Gear, 26 T. for 7/8 in. dia. Middle and Back Rolls, 24 T. for 15/16 in. dia. Middle and 1-1/16 in. dia. Back Rolls.
I Whorl, 3/4 in., 13/16 in. and 7/8 in. dia.
J Carrier Sprocket Gear, 10 T.
K Builder Motion Worm Shaft Sprocket Gear, 12, 14, 16, 18, 20, 22 and 24 T., dependent upon the Number of Yarn.
L Carrier Sprocket Gear, 7 T.
{164}
SPINNING FRAMES.
DRAFT CALCULATIONS.
TWIST CALCULATIONS.
[Ill.u.s.tration]
When figuring the Ratio of Whirl Speed to Cylinder Speed we add 1/3 inch to the diameters to allow for the band.
{165}
[Ill.u.s.tration]
In our production tables on pages 156 to 159, the allowance for doffing, waste, etc., varies with the numbers of yarn, the percentage loss being greater for coa.r.s.e than fine work.
{166}
RING SPINNING FRAME, DRAFT TABLE.
FRONT ROLL 1 IN. DIAM. BACK ROLL 7/8 IN. DIAM.
[Ill.u.s.tration]
{167}
RING SPINNING FRAME, DRAFT TABLE.
FRONT AND BACK ROLLS SAME DIAMETER.
[Ill.u.s.tration]
{168}
RING SPINNING FRAME, TWIST CONSTANTS.
1 IN. DIA. FRONT ROLL. 7 IN. DIA. CYLINDER.
FRONT ROLL GEAR, 84 T.
[Ill.u.s.tration]
{169}
RING SPINNING FRAME, TWIST CONSTANTS.
