Home

Steam, Its Generation and Use Part 16

Steam, Its Generation and Use - novelonlinefull.com

You’re read light novel Steam, Its Generation and Use Part 16 online at NovelOnlineFull.com. Please use the follow button to get notification about the latest chapter next time when you visit NovelOnlineFull.com. Use F11 button to read novel in full-screen(PC only). Drop by anytime you want to read free – fast – latest novel. It’s great if you could leave a comment, share your opinion about the new chapters, new novel with others on the internet. We’ll do our best to bring you the finest, latest novel everyday. Enjoy

It would appear that the nozzle ill.u.s.trated is undoubtedly the best that has been developed for use in the determination of the moisture content of steam, not only in the case of low, but also in high pressure steam.

Location of Sampling Nozzle--The calorimeter should be located as near as possible to the point from which the steam is taken and the sampling nipple should be placed in a section of the main pipe near the boiler and where there is no chance of moisture pocketing in the pipe. The American Society of Mechanical Engineers recommends that a sampling nipple, of which a description has been given, should be located in a vertical main, rising from the boiler with its closed end extending nearly across the pipe. Where non-return valves are used, or where there are horizontal connections leading from the boiler to a vertical outlet, water may collect at the lower end of the uptake pipe and be blown upward in a spray which will not be carried away by the steam owing to a lack of velocity. A sample taken from the lower part of this pipe will show a greater amount of moisture than a true sample. With goose-neck connections a small amount of water may collect on the bottom of the pipe near the upper end where the inclination is such that the tendency to flow backward is ordinarily counterbalanced by the flow of steam forward over its surface; but when the velocity momentarily decreases the water flows back to the lower end of the goose-neck and increases the moisture at that point, making it an undesirable location for sampling. In any case, it should be borne in mind that with low velocities the tendency is for drops of entrained water to settle to the bottom of the pipe, and to be temporarily broken up into spray whenever an abrupt bend or other disturbance is met.

[Ill.u.s.tration: Fig. 19. Ill.u.s.trating the Manner in which Erroneous Calorimeter Readings may be Obtained due to Improper Location of Sampling Nozzle

Case 1--Horizontal pipe. Water flows at bottom. If perforations in nozzle are too near bottom of pipe, water piles against nozzle, flows into calorimeter and gives false reading.

Case 2--If nozzle located too near junction of two horizontal runs, as at a, condensation from vertical pipe which collects at this point will be thrown against the nozzle by the velocity of the steam, resulting in a false reading. Nozzle should be located far enough above junction to be removed from water kept in motion by the steam velocity, as at b. Case 3--Condensation in bend will be held by velocity of the steam as shown. When velocity is diminished during firing intervals and the like moisture flows back against nozzle, a, and false reading is obtained. A true reading will be obtained at b provided condensation is not blown over on nozzle. Case 4--Where non-return valve is placed before a bend, condensation will collect on steam line side and water will be swept by steam velocity against nozzle and false readings result.]

Fig. 19 indicates certain locations of sampling nozzles from which erroneous results will be obtained, the reasons being obvious from a study of the cuts.

Before taking any calorimeter reading, steam should be allowed to flow through the instrument freely until it is thoroughly heated. The method of using a throttling calorimeter is evident from the description of the instrument given and the principle upon which it works.

[Ill.u.s.tration: Babc.o.c.k & Wilc.o.x Superheater]

SUPERHEATED STEAM

Superheated steam, as already stated, is steam the temperature of which exceeds that of saturated steam at the same pressure. It is produced by the addition of heat to saturated steam which has been removed from contact with the water from which it was generated. The properties of superheated steam approximate those of a perfect gas rather than of a vapor. Saturated steam cannot be superheated when it is in contact with water which is also heated, neither can superheated steam condense without first being reduced to the temperature of saturated steam. Just so long as its temperature is above that of saturated steam at a corresponding pressure it is superheated, and before condensation can take place that superheat must first be lost through radiation or some other means. Table 24[20] gives such properties of superheated steam for varying pressures as are necessary for use in ordinary engineering practice.

Specific Heat of Superheated Steam--The specific heat of superheated steam at atmospheric pressure and near saturation point was determined by Regnault, in 1862, who gives it the value of 0.48. Regnault's value was based on four series of experiments, all at atmospheric pressure and with about the same temperature range, the maximum of which was 231.1 degrees centigrade. For fifty years after Regnault's determination, this value was accepted and applied to higher pressures and temperatures as well as to the range of his experiments. More recent investigations have shown that the specific heat is not a constant and varies with both pressure and the temperature. A number of experiments have been made by various investigators and, up to the present, the most reliable appear to be those of k.n.o.blauch and Jacob. Messrs. Marks and Davis have used the values as determined by k.n.o.blauch and Jacob with slight modifications. The first consists in a varying of the curves at low pressures close to saturation because of thermodynamic evidence and in view of Regnault's determination at atmospheric pressure. The second modification is at high degrees of superheat to follow Holborn's and Henning's curve, which is accepted as authentic.

For the sake of convenience, the mean specific heat of superheated steam at various pressures and temperatures is given in tabulated form in Table 25. These values have been calculated from Marks and Davis Steam Tables by deducting from the total heat of one pound of steam at any pressure for any degree of superheat the total heat of one pound of saturated steam at the same pressure and dividing the difference by the number of degrees of superheat and, therefore, represent the average specific heat starting from that at saturation to the value at the particular pressure and temperature.[21] Expressed as a formula this calculation is represented by

H_{sup} - H_{sat} Sp. Ht. = ----------------- (8) S_{sup} - S_{sat}

Where H_{sup} = total heat of one pound of superheated steam at any pressure and temperature, H_{sat} = total heat of one pound of saturated steam at same pressure, S_{sup} = temperature of superheated steam taken, S_{sat} = temperature of saturated steam corresponding to the pressure taken.

TABLE 25

MEAN SPECIFIC HEAT OF SUPERHEATED STEAM CALCULATED FROM MARKS AND DAVIS TABLES _______________________________________________________________ |Gauge | | |Pressure | Degree of Superheat | | |_____________________________________________________| | | 50 | 60 | 70 | 80 | 90 | 100 | 110 | 120 | 130 | |_________|_____|_____|_____|_____|_____|_____|_____|_____|_____| | 50 | .518| .517| .514| .513| .511| .510| .508| .507| .505| | 60 | .528| .525| .523| .521| .519| .517| .515| .513| .512| | 70 | .536| .534| .531| .529| .527| .524| .522| .520| .518| | 80 | .544| .542| .539| .535| .532| .530| .528| .526| .524| | 90 | .553| .550| .546| .543| .539| .536| .534| .532| .529| | 100 | .562| .557| .553| .549| .544| .542| .539| .536| .533| | 110 | .570| .565| .560| .556| .552| .548| .545| .542| .539| | 120 | .578| .573| .567| .561| .557| .554| .550| .546| .543| | 130 | .586| .580| .574| .569| .564| .560| .555| .552| .548| | 140 | .594| .588| .581| .575| .570| .565| .561| .557| .553| | 150 | .604| .595| .587| .581| .576| .570| .566| .561| .557| | 160 | .612| .603| .596| .589| .582| .576| .571| .566| .562| | 170 | .620| .612| .603| .595| .588| .582| .576| .571| .566| | 180 | .628| .618| .610| .601| .593| .587| .581| .575| .570| | 190 | .638| .627| .617| .608| .599| .592| .585| .579| .574| | 200 | .648| .635| .624| .614| .605| .597| .590| .584| .578| | 210 | .656| .643| .631| .620| .611| .602| .595| .588| .583| | 220 | .664| .650| .637| .626| .616| .607| .600| .592| .586| | 230 | .672| .658| .644| .633| .622| .613| .605| .597| .591| | 240 | .684| .668| .653| .640| .629| .619| .610| .602| .595| | 250 | .692| .675| .659| .645| .633| .623| .614| .606| .599| |_________|_____|_____|_____|_____|_____|_____|_____|_____|_____| |Gauge | | |Pressure | Degree of Superheat | | |-----------------------------------------------------| | | 140 | 150 | 160 | 170 | 180 | 190 | 200 | 225 | 250 | |---------+-----+-----+-----+-----+-----+-----+-----+-----+-----| | 50 | .504| .503| .502| .501| .500| .500| .499| .497| .496| | 60 | .511| .509| .508| .507| .506| .504| .504| .502| .500| | 70 | .516| .515| .513| .512| .511| .510| .509| .506| .504| | 80 | .522| .520| .518| .516| .515| .514| .513| .511| .508| | 90 | .527| .525| .523| .521| .519| .518| .517| .514| .510| | 100 | .531| .529| .527| .525| .523| .522| .521| .517| .513| | 110 | .536| .534| .532| .529| .528| .526| .525| .520| .517| | 120 | .540| .537| .535| .533| .531| .529| .528| .523| .519| | 130 | .545| .542| .539| .537| .535| .533| .531| .527| .523| | 140 | .550| .547| .544| .541| .539| .536| .534| .530| .526| | 150 | .554| .550| .547| .544| .542| .539| .537| .533| .529| | 160 | .558| .554| .551| .548| .545| .543| .541| .536| .531| | 170 | .562| .558| .555| .552| .549| .546| .544| .538| .533| | 180 | .566| .561| .558| .555| .552| .549| .546| .540| .536| | 190 | .569| .565| .562| .558| .555| .552| .549| .543| .538| | 200 | .574| .569| .566| .562| .558| .555| .552| .546| .541| | 210 | .578| .573| .569| .565| .561| .558| .555| .549| .543| | 220 | .581| .577| .572| .568| .564| .561| .558| .551| .545| | 230 | .585| .580| .575| .572| .567| .564| .561| .554| .548| | 240 | .589| .584| .579| .575| .571| .567| .564| .556| .550| | 250 | .593| .587| .582| .577| .574| .570| .567| .559| .553| |_________|_____|_____|_____|_____|_____|_____|_____|_____|_____|

Factor of Evaporation with Superheated Steam--When superheat is present in the steam during a boiler trial, where superheated steam tables are available, the formula for determining the factor of evaporation is that already given, (2),[22] namely,

H - h Factor of evaporation = ----- L

Here H = total heat in one pound of superheated steam from the table, h and L having the same values as in (2).

Where no such tables are available but the specific heat of superheat is known, the formula becomes:

H - h + Sp. Ht.(T - t) Factor of evaporation = ---------------------- L

Where H = total heat in one pound of saturated steam at pressure existing in trial, h = sensible heat above 32 degrees in one pound of water at the temperature entering the boiler, T = temperature of superheated steam as determined in the trial, t = temperature of saturated steam corresponding to the boiler pressure, Sp. Ht. = mean specific heat of superheated steam at the pressure and temperature as found in the trial, L = latent heat of one pound of saturated steam at atmospheric pressure.

Advantages of the Use of Superheated Steam--In considering the saving possible by the use of superheated steam, it is too often a.s.sumed that there is only a saving in the prime movers, a saving which is at least partially offset by an increase in the fuel consumption of the boilers generating steam. This misconception is due to the fact that the fuel consumption of the boiler is only considered in connection with a definite weight of steam. It is true that where such a definite weight is to be superheated, an added amount of fuel must be burned. With a properly designed superheater where the combined efficiency of the boiler and superheater will be at least as high as of a boiler alone, the approximate increase in coal consumption for producing a given weight of steam will be as follows:

_Superheat_ _Added Fuel_ _Degrees_ _Per Cent_ 25 1.59 50 3.07 75 4.38 100 5.69 150 8.19 200 10.58

These figures represent the added fuel necessary for superheating a definite weight of steam to the number of degrees as given. The standard basis, however, of boiler evaporation is one of heat units and, considered from such a standpoint, again providing the efficiency of the boiler and superheater is as high, as of a boiler alone, there is no additional fuel required to generate steam containing a definite number of heat units whether such units be due to superheat or saturation. That is, if 6 per cent more fuel is required to generate and superheat to 100 degrees, a definite weight of steam, over what would be required to produce the same weight of saturated steam, that steam when superheated, will contain 6 per cent more heat units above the fuel water temperature than if saturated. This holds true if the efficiency of the boiler and superheater combined is the same as of the boiler alone. As a matter of fact, the efficiency of a boiler and superheater, where the latter is properly designed and located, will be slightly higher for the same set of furnace conditions than would the efficiency of a boiler in which no superheater were installed. A superheater, properly placed within the boiler setting in such way that products of combustion for generating saturated steam are utilized as well for superheating that steam, will not in any way alter furnace conditions. With a given set of such furnace conditions for a given amount of coal burned, the fact that additional surface, whether as boiler heating or superheating surface, is placed in such a manner that the gases must sweep over it, will tend to lower the temperature of the exit gases. It is such a lowering of exit gas temperatures that is the ultimate indication of added efficiency. Though the amount of this added efficiency is difficult to determine by test, that there is an increase is unquestionable.

Where a properly designed superheater is installed in a boiler the heating surface of the boiler proper, in the generation of a definite number of heat units, is relieved of a portion of the work which would be required were these heat units delivered in saturated steam. Such a superheater needs practically no attention, is not subject to a large upkeep cost or depreciation, and performs its function without in any way interfering with the operation of the boiler. Its use, therefore from the standpoint of the boiler room, results in a saving in wear and tear due to the lower ratings at which the boiler may be run, or its use will lead to the possibility of obtaining the same number of boiler horse power from a smaller number of boilers, with the boiler heating surface doing exactly the same amount of work as if the superheaters were not installed. The saving due to the added boiler efficiency that will be obtained is obvious.

Following the course of the steam in a plant, the next advantage of the use of superheated steam is the absence of water in the steam pipes. The thermal conductivity of superheated steam, that is, its power to give up its heat to surrounding bodies, is much lower than that of saturated steam and its heat, therefore, will not be transmitted so rapidly to the walls of the pipes as when saturated steam is flowing through the pipes.

The loss of heat radiated from a steam pipe, a.s.suming no loss in pressure, represents the equivalent condensation when the pipe is carrying saturated steam. In well-covered steam mains, the heat lost by radiation when carrying superheated steam is accompanied only by a reduction of the superheat which, if it be sufficiently high at the boiler, will enable a considerable amount of heat to be radiated and still deliver dry or superheated steam to the prime movers.

It is in the prime movers that the advantages of the use of superheated steam are most clearly seen.

In an engine, steam is admitted into a s.p.a.ce that has been cooled by the steam exhausted during the previous stroke. The heat necessary to warm the cylinder walls from the temperature of the exhaust to that of the entering steam can be supplied only by the entering steam. If this steam be saturated, such an adding of heat to the walls at the expense of the heat of the entering steam results in the condensation of a portion.

This initial condensation is seldom less than from 20 to 30 per cent of the total weight of steam entering the cylinder. It is obvious that if the steam entering be superheated, it must be reduced to the temperature of saturated steam at the corresponding pressure before any condensation can take place. If the steam be superheated sufficiently to allow a reduction in temperature equivalent to the quant.i.ty of heat that must be imparted to the cylinder walls and still remain superheated, it is clear that initial condensation is avoided. For example: a.s.sume one pound of saturated steam at 200 pounds gauge pressure to enter a cylinder which has been cooled by the exhaust. a.s.sume the initial condensation to be 20 per cent. The latent heat of the steam is given up in condensation; hence, .20 838 = 167.6 B. t. u. are given up by the steam. If one pound of superheated steam enters the same cylinder, it would have to be superheated to a point where its total heat is 1199 + 168 = 1367 B. t. u. or, at 200 pounds gauge pressure, superheated approximately 325 degrees if the heat given up to the cylinder walls were the same as for the saturated steam. As superheated steam conducts heat less rapidly than saturated steam, the amount of heat imparted will be less than for the saturated steam and consequently the amount of superheat required to prevent condensation will be less than the above figure. This, of course, is the extreme case of a simple engine with the range of temperature change a maximum. As cylinders are added, the range in each is decreased and the condensation is proportionate.

The true economy of the use of superheated steam is best shown in a comparison of the "heat consumption" of an engine. This is the number of heat units required in developing one indicated horse power and the measure of the relative performance of two engines is based on a comparison of their heat consumption as the measure of a boiler is based on its evaporation from and at 212 degrees. The water consumption of an engine in pounds per indicated horse power is in no sense a true indication of its efficiency. The initial pressures and corresponding temperatures may differ widely and thus make a difference in the temperature of the exhaust and hence in the temperature of the condensed steam returned to the boiler. For example: suppose a certain weight of steam at 150 pounds absolute pressure and 358 degrees be expanded to atmospheric pressure, the temperature then being 212 degrees. If the same weight of steam be expanded from an initial pressure of 125 pounds absolute and 344 degrees, to enable it to do the same amount of work, that is, to give up the same amount of heat, expansion then must be carried to a point below atmospheric pressure to, say, 13 pounds absolute, the final temperature of the steam then being 206 degrees. In actual practice, it has been observed that the water consumption of a compound piston engine running on 26-inch vacuum and returning the condensed steam at 140 degrees was approximately the same as when running on 28-inch vacuum and returning water at 90 degrees. With an equal water consumption for the two sets of conditions, the economy in the former case would be greater than in the latter, since it would be necessary to add less heat to the water returned to the boiler to raise it to the steam temperature.

The lower the heat consumption of an engine per indicated horse power, the higher its economy and the less the number of heat units must be imparted to the steam generated. This in turn leads to the lowering of the amount of fuel that must be burned per indicated horse power.

With the saving in fuel by the reduction of heat consumption of an engine indicated, it remains to be shown the effect of the use of superheated steam on such heat consumption. As already explained, the use of superheated steam reduces condensation not only in the mains but especially in the steam cylinder, leaving a greater quant.i.ty of steam available to do the work. Furthermore, a portion of the saturated steam introduced into a cylinder will condense during adiabatic expansion, this condensation increasing as expansion progresses. Since superheated steam cannot condense until it becomes saturated, not only is initial condensation prevented by its use but also such condensation as would occur during expansion. When superheated sufficiently, steam delivered by the exhaust will still be dry. In the avoidance of such condensation, there is a direct saving in the heat consumption of an engine, the heat given up being utilized in the developing of power and not in changing the condition of the working fluid. That is, while the number of heat units lost in overcoming condensation effects would be the same in either case, when saturated steam is condensed the water of condensation has no power to do work while the superheated steam, even after it has lost a like number of heat units, still has the power of expansion. The saving through the use of superheated steam in the heat consumption of an engine decreases demands on the boiler and hence the fuel consumption per unit of power.

Superheated Steam for Steam Turbines--Experience in using superheated steam in connection with steam turbines has shown that it leads to economy and that it undoubtedly pays to use superheated steam in place of saturated steam. This is so well established that it is standard practice to use superheated steam in connection with steam turbines.

Aside from the economy secured through using superheated steam, there is an important advantage arising through the fact that it materially reduces the erosion of the turbine blades by the action of water that would be carried by saturated steam. In using saturated steam in a steam turbine or piston engine, the work done on expanding the steam causes condensation of a portion of the steam, so that even were the steam dry on entering the turbine, it would contain water on leaving the turbine.

By superheating the steam the water that exists in the low pressure stages of the turbine may be reduced to an amount that will not cause trouble.

Again, if saturated steam contains moisture, the effect of this moisture on the economy of a steam turbine is to reduce the economy to a greater extent than the proportion by weight of water, one per cent of water causing approximately a falling off of 2 per cent in the economy.

The water rate of a large economical steam turbine with superheated steam is reduced about one per cent, for every 12 degrees of superheat up to 200 degrees Fahrenheit of superheat. To superheat one pound of steam 12 degrees requires about 7 B. t. u. and if 1050 B. t. u. are required at the boiler to evaporate one pound of the saturated steam from the temperature of the feed water, the heat required for the superheated steam would be 1057 degrees. One per cent of saving, therefore, in the water consumption would correspond to a net saving of about one-third of one per cent in the coal consumption. On this basis 100 degrees of superheat with an economical steam turbine would result in somewhat over 3 per cent of saving in the coal for equal boiler efficiencies. As a boiler with a properly designed superheater placed within the setting is more economical for a given capacity than a boiler without a superheater, the minimum gain in the coal consumption would be, say, 4 or 5 per cent as compared to a plant with the same boilers without superheaters.

The above estimates are on the basis of a thoroughly dry saturated steam or steam just at the point of being superheated or containing a few degrees of superheat. If the saturated steam is moist, the saving due to superheat is more and ordinarily the gain in economy due to superheated steam, for equal boiler efficiencies, as compared with commercially dry steam is, say, 5 per cent for each 100 degrees of superheat. Aside from this gain, as already stated, superheated steam prevents erosion of the turbine buckets that would be caused by water in the steam, and for the reasons enumerated it is standard practice to use superheated steam for turbine work. The less economical the steam motor, the more the gain due to superheated steam, and where there are a number of auxiliaries that are run with superheated steam, the percentage of gain will be greater than the figures given above, which are the minimum and are for the most economical type of large steam turbines.

An example from actual practice will perhaps best ill.u.s.trate and emphasize the foregoing facts. In October 1909, a series of comparable tests were conducted by The Babc.o.c.k & Wilc.o.x Co. on the steam yacht "Idalia" to determine the steam consumption both with saturated and superheated steam of the main engine on that yacht, including as well the feed pump, circulating pump and air pump. These tests are more representative than are most tests of like character in that the saving in the steam consumption of the auxiliaries, which were much more wasteful than the main engine, formed an important factor. A resume of these tests was published in the Journal of the Society of Naval Engineers, November 1909.

The main engines of the "Idalia" are four cylinder, triple expansion, 11-1/2 19 inches by 22-11/16 18 inches stroke. Steam is supplied by a Babc.o.c.k & Wilc.o.x marine boiler having 2500 square feet of boiler heating surface, 340 square feet of superheating surface and 65 square feet of grate surface.

The auxiliaries consist of a feed pump 6 4 6 inches, an independent air pump 6 12 8 inches, and a centrifugal pump driven by a reciprocating engine 5-7/16 5 inches. Under ordinary operating conditions the superheat existing is about 100 degrees Fahrenheit.

Tests were made with various degrees of superheat, the amount being varied by by-pa.s.sing the gases and in the tests with the lower amounts of superheat by pa.s.sing a portion of the steam from the boiler to the steam main without pa.s.sing it through the superheater. Steam temperature readings were taken at the engine throttle. In the tests with saturated steam, the superheater was completely cut out of the system. Careful calorimeter measurements were taken, showing that the saturated steam delivered to the superheater was dry.

The weight of steam used was determined from the weight of the condensed steam discharge from the surface condenser, the water being pumped from the hot well into a tank mounted on platform scales. The same indicators, thermometers and gauges were used in all the tests, so that the results are directly comparable. The indicators used were of the outside spring type so that there was no effect of the temperature of the steam. All tests were of sufficient duration to show a uniformity of results by hours. A summary of the results secured is given in Table 26, which shows the water rate per indicated horse power and the heat consumption. The latter figures are computed on the basis of the heat imparted to the steam above the actual temperature of the feed water and, as stated, these are the results that are directly comparable.

TABLE 26

RESULTS OF "IDALIA" TESTS _______________________________________________________________________ | | | | | | | |Date 1909 |Oct. 11|Oct. 14|Oct. 14|Oct. 12|Oct. 13| |_______________________________|_______|_______|_______|_______|_______| |Degrees of superheat Fahrenheit| 0 | 57 | 88 | 96 | 105 | |Pressures, pounds per} Throttle| 190 | 196 | 201 | 198 | 203 | |square inch above } First | | | | | | |Atmospheric Pressure } Receiver| 68.4 | 66.0 | 64.3 | 61.9 | 63.0 | | } Second | | | | | | | } Receiver| 9.7 | 9.2 | 8.7 | 7.8 | 8.4 | |Vacuum, inches | 25.5 | 25.9 | 25.9 | 25.4 | 25.2 | |Temperature, Degrees Fahrenheit| | | | | | | } Feed | 201 | 206 | 205 | 202 | 200 | | } Hot Well | 116 | 109.5 | 115 | 111.5 | 111 | | | | | | | | |Revolutions per minute | | | | | | | {Air Pump | 57 | 56 | 53 | 54 | 45 | | {Circulating Pump| 196 | 198 | 196 | 198 | 197 | | {Main Engine | 194.3 | 191.5 | 195.1 | 191.5 | 193.1 | |Indicated Horse Power, | | | | | | | Main Engine | 512.3 | 495.2 | 521.1 | 498.3 | 502.2 | |Water per hour, total pounds |9397 |8430 |8234 |7902 |7790 | |Water per indicated | | | | | | | Horse Power, pounds | 18.3 | 17.0 | 15.8 | 15.8 | 15.5 | |B. t. u. per minute per | | | | | | | indicated Horse Power | 314 | 300 | 284 | 286 | 283 | |Per cent Saving of Steam | ... | 7.1 | 13.7 | 13.7 | 15.3 | |Percent Saving of Fuel | | | | | | | (computed) | ... | 4.4 | 9.5 | 8.9 | 9.9 | |_______________________________|_______|_______|_______|_______|_______|

The table shows that the saving in steam consumption with 105 degrees of superheat was 15.3 per cent and in heat consumption about 10 per cent.

This may be safely stated to be a conservative representation of the saving that may be accomplished by the use of superheated steam in a plant as a whole, where superheated steam is furnished not only to the main engine but also to the auxiliaries. The figures may be taken as conservative for the reason that in addition to the saving as shown in the table, there would be in an ordinary plant a saving much greater than is generally realized in the drips, where the loss with saturated steam is greatly in excess of that with superheated steam.

The most conclusive and most practical evidence that a saving is possible through the use of superheated steam is in the fact that in the largest and most economical plants it is used almost without exception.

Regardless of any such evidence, however, there is a deep rooted conviction in the minds of certain engineers that the use of superheated steam will involve operating difficulties which, with additional first cost, will more than offset any fuel saving. There are, of course, conditions under which the installation of superheaters would in no way be advisable. With a poorly designed superheater, no gain would result.

In general, it may be stated that in a new plant, properly designed, with a boiler and superheater which will have an efficiency at least as high as a boiler without a superheater, a gain is certain.

Please click Like and leave more comments to support and keep us alive.

RECENTLY UPDATED MANGA

The Grand Secretary's Pampered Wife

The Grand Secretary's Pampered Wife

The Grand Secretary's Pampered Wife Chapter 574.1: JiaoJiao and Long Yi Author(s) : Pian Fang Fang, 偏方方, Folk Remedies, Home Remedy View : 243,970
My Rich Wife

My Rich Wife

My Rich Wife Chapter 2679: The Miracle Author(s) : Taibai And A Qin View : 1,540,287
Overgeared

Overgeared

Overgeared Chapter 2011 Author(s) : Park Saenal View : 12,414,287
Tondemo Skill de Isekai Hourou Meshi

Tondemo Skill de Isekai Hourou Meshi

Tondemo Skill de Isekai Hourou Meshi Chapter 602: Easy Bacon-Style Porkbelly Author(s) : 妖精壱号, Yosei Ichigo, Eguchi Ren, 江口連 View : 2,393,641
I am a Gao Fushuai Villain

I am a Gao Fushuai Villain

I am a Gao Fushuai Villain Chapter 608: Author(s) : 向往的都市神豪 View : 621,659

Steam, Its Generation and Use Part 16 summary

You're reading Steam, Its Generation and Use. This manga has been translated by Updating. Author(s): Babcock & Wilcox Company. Already has 643 views.

It's great if you read and follow any novel on our website. We promise you that we'll bring you the latest, hottest novel everyday and FREE.

NovelOnlineFull.com is a most smartest website for reading manga online, it can automatic resize images to fit your pc screen, even on your mobile. Experience now by using your smartphone and access to NovelOnlineFull.com