Practical Lithography Part 1

Practical Lithography.

by Alfred Seymour.

INTRODUCTION

"Alois Senefelder never benefited much by his discovery of the elementary principles of lithography, but none of those to whom it has given profitable occupation will remember without some feeling the patient and persistent efforts of the struggling actor and dramatist who, only after the greatest sacrifices and hardships, laid the germ of this splendid development, and watched and guarded its growth." There is one characteristic feature of the discovery of lithography for which Senefelder ought to receive the fullest credit. Unlike other discoveries of industrial and scientific value, there can be no doubt whatever as to its origin. Senefelder's claim has never been disputed, yet "the payment of a debt of grat.i.tude to the fact is easily overlooked when the wheel of history has made another turn."

It has been again and again suggested that the blighting influences of Commercialism have robbed lithography of many of its traditional features and a few, at least, of its best and most artistic qualities as a reproductive art. This same commercial spirit, however, has inspired and encouraged a charming variety of effect both in colour and design, and lithography of to-day, in almost every form of its manifestation, is infinitely more attractive and capable of considerably more expressive power than could ever have been hoped for before commercial utility and value demanded a full recognition. Pleasing and harmonious effects, which are almost invariably sought after in lithography, need not be inartistic; and it is quite possible for the technique of the lithographic draughtsman to translate original work without a serious depreciation of its pictorial and artistic value.

While expressing a sincere hope that this volume may be of considerable a.s.sistance to his fellow-craftsmen, the writer wishes to emphasise the fact that resourcefulness and intelligent application are faculties which may be encouraged and amplified but cannot be imparted even by volumes of text.

A mere formal acknowledgment of a.s.sistance cordially rendered by the editors of the _British Printer_ and _The Caxton Magazine_ and _Press_, Messrs. Penrose & Co., and other firms whose blocks are _prima facie_ evidences of their interest, does not adequately express the appreciation with which it has been accepted and made use of.

A. S.

LONDON, _December 1903_.

CHAPTER I

ELEMENTARY DETAILS

Concerning Stones--Character and Texture--Some Simple Elements--Preparation of Stones--Planing and Levelling-- Grinding Grained Stones--Descriptive Treatment--American Method.

There are a vast number of details in connection with lithography and lithographic printing which are indisputably elementary in their character. It would be impossible, however, to regard them as non-essential, and a just appreciation of their value and influence must of necessity enter into any comprehensive exposition of the craft.

_Stone as a printing medium._--The value of the Bavarian limestone was one of those fortunate discoveries which tended to materialise lithography as a graphic art, and may even be regarded as a fundamental principle, the practical value of which is only equalled by its far-reaching effects.

Other printing surfaces have been discovered and developed, with more or less substantial results, yet without depreciating their merits, it will be but a fair recognition to concede the premier position to the Solenhofen and other limestones of a like nature.

The h.o.m.ogeneity and porosity of these stones render them peculiarly suitable for lithographic purposes, and it undoubtedly reflects a vast amount of credit upon Senefelder that even at the outset he should select a medium so well adapted and in every way so eminently suitable for graphic reproduction.

I have already, and almost inadvertently, indicated the peculiar value of the Bavarian stone, for h.o.m.ogeneity and porosity of texture are absolutely essential properties, and upon these is based almost every theory which has a.s.sisted in the development of this craft. These properties, in conjunction with a suitable greasy pigment, provide the requisite materials for that cause and effect which require and compel consideration.

The simple elements of lithography may be very briefly described, and in this direction at least we must follow certain well-defined lines which may be regarded as well-worn ruts, the consideration of which offers little that is new.

A brief review of the theories of chemical and mechanical affinities is best calculated to impress upon the mind the elementary principles of the lithographer's art.

The penetrative power of a greasy pigment, together with the porous nature of the litho-stone, may be regarded as the cause by which the lithographer produces as an effect a design or impression which, to some extent, enters into the texture of the stone--the h.o.m.ogeneity of which checks any tendency to _spread_. This fatty matter may be applied in one or two ways, either as a transfer from some other printing surface, or as a direct drawing with pen, brush, or crayon.

The first question for consideration will be the initial preparation of the litho-stones. These preparatory operations--which have for their object the levelling, polishing, and cleaning of the stones--were at one time entirely performed by hand labour, but are now accomplished with much greater facility and in a more effective manner by machinery. The importance of each individual operation will be more readily appreciated when once its purpose is clearly understood. A litho-stone having a _perfectly level_ surface is necessary in order to enable the printer to secure a firm and uniform pressure over the whole design when printing therefrom. A _smooth_, _polished_ surface will readily receive the finest designs, and retain all their original characteristics. A _clean_ surface is an absolute necessity, _i.e._ a chemically clean surface free from grease or any foreign matter which would be likely to enter into the texture of the stone and by so doing injure any greasy drawing or transfer which might be made thereon.

These are simple, elementary principles, and as such are probably familiar to every reader, but the frequent result of familiarity is a dangerous tendency to under-estimate the importance of everyday causes and effects. If, therefore, such a reference as the above to common details serves to convey some intelligent idea of their place and true value, then no apology whatever will be necessary for their insertion in this volume. It has already been stated that, in the preparation of litho-stones, the superseding of hand labour by machinery has effected considerable and important changes.

Several machines, all of more or less practical value, have been introduced to the trade. One of the more recent developments, a stone-planing machine, possesses many features of real merit (Fig. 1).

The stone is securely fixed on a perfectly true bed and pa.s.ses slowly to and fro beneath the blades of powerful cutting knives. These blades are arranged in an inverted V-shape and locked in an oscillating framework.

By an automatic action they are almost imperceptibly lowered at each traverse of the machine, when they lightly cut away the surface of the stone until the old work is completely removed and a smooth level face is a.s.sured. The chief objection to this type of machine is that in course of time the knives become worn and slightly irregular, and it is but reasonable to suppose that when a number of small stones have been operated upon and immediately afterwards a full-sized stone is planed, such irregularities will be very p.r.o.nounced and detrimental.

[Ill.u.s.tration: FIG. 1.]

Many machines have been designed on the simple grinding principle, but one type differs from its contemporaries and offers several distinct advantages over them (Fig. 2).

This machine is constructed on hand-polishing lines, _i.e._ the movements are to some extent mechanical arrangements of hand-polishing principles. The size of stone makes no difference whatever, and the results are in the main uniform and satisfactory. The inconveniently sharp edges, such as are produced by the planing machine, are unknown,--the wear and tear on the stone is perceptibly lessened, and the power required to drive such a machine is not by any means a serious matter.

When a planing machine does not enter into the operation, and grinding by hand is therefore necessary, sharp, clean sand should be used as a grinding medium. To secure some degree of uniformity in the grain, and at the same time remove all the larger particles of grit, pa.s.s the sand first through a fine sieve. The harder qualities of sand have, of course, the greatest cutting power, and therefore are the most suitable for this purpose.

[Ill.u.s.tration: FIG. 2.]

When hand-grinding is resorted to, a continuous elliptical motion of one stone over the other with a slight twist from the wrist will prove most effective.

To finish the grinding, and as far as possible remove the deeper sand scratches, work off the sand in the form of a _sludge_. Unless this operation is carefully and patiently performed, scratches of considerable depth may appear on various parts of the stone's surface.

These, in the subsequent polishing, may offer a strong temptation to the operator to work over one part of the stone more than another, so as to effect the removal of such scratches with greater rapidity. The almost certain result of this would be an uneven surface, which would in many ways prove troublesome to the printer.

_The graining of stones._--This is a matter concerning the preparation of stones which must not be overlooked. The introduction of shading mediums and other contrivances of a similar character has considerably minimised the importance of the grained stone, inasmuch as it cannot now be regarded as an indispensable feature of lithography. It is, however, still of inestimable value, and will probably always find a place and purpose in the practice of lithography, despite its depreciation owing to present-day limitations.

Recognising, then, the possibility of its retention, at least for some time to come, as a suitable printing surface upon which the lithographic draughtsman can work with undoubted facility of execution and effect, we must perforce include a brief description of its preparation in this chapter.

First of all, level the stone and to some extent polish it, after which the graining may be proceeded with. A gla.s.s muller about 6 or 7 inches in diameter makes an excellent "grainer." Failing this, a handy subst.i.tute will be found in the form of a small litho-stone, hard in texture, and with a smooth, level surface. Use as a graining medium sharp, clean silver sand only, pa.s.sing it carefully through a sieve according to the size or depth of the grain required. Sprinkle a little of this sand uniformly over the stone under treatment, together with a few drops of clean water. With a continuous circular movement pa.s.s the graining muller from end to end of the stone, exerting a firm and uniform pressure. Repeat this operation again and again, adding sand and water as required. Considerable time coupled with intelligent application will be necessary to carry out this work successfully.

Should the sand become too much worn before its renewal the grain will in proportion lose its "tooth" or sharpness. On the other hand lies the danger of producing a grain which is too harsh or p.r.o.nounced. Therefore much depends upon the skill and judgment of the operator. A safe plan is to ascertain the progress at any time when a satisfactory result might be reasonably expected. The best way to accomplish this is by washing from the face of the stone any acc.u.mulation of sand, and drying it, so that a test can be made with the actual grade of crayon to be used in the subsequent drawing. A powerful current of clean, cold water affords the best means for removing every trace of sand from the finished stone, and will leave it in a condition of almost complete readiness for the draughtsman; a good drying is then all that is necessary. Good results have been claimed for a method of graining which was introduced by the Americans a few years ago. In this process the grain is produced by sprinkling the surface of the stone with sand and rolling it with small gla.s.s b.a.l.l.s. These b.a.l.l.s having a limited area in which to work exert a continuous cutting power without any tendency to produce scratches. Some mechanical arrangement is necessary to impart this continuous rolling movement to the gla.s.s b.a.l.l.s and to maintain a uniform speed. It is quite easy to understand that with such a process, carried out under favourable conditions, very fine results might be produced with great rapidity.

CHAPTER II

LITHOGRAPHIC TRANSFER INKS

Various Forms--Distinguishing Features--Formulae--Writing Transfer Ink--Stone-to-stone Transfer Ink--Copperplate Transfer Ink--A Modification.

Given a perfectly clean and smooth polished stone as described in the previous chapter, the next important point is the composition of the fatty matter wherewith a design or drawing is applied.

As already stated, the active principle in any suitable transfer medium of this character is invariably the same, no matter what form its composition takes. For applying with pen or brush it must possess soluble properties, and of necessity be reduced to a liquid form. Such soluble properties, however, must not interfere with its fatty properties, these latter being essential features.

In crayon or _chalk_ drawing the composition must be employed in a concrete form, as a crayon, the hardness and texture of which will be controlled (1) by the character of the work to be carried out; (2) by the character of surface to be operated upon.

Transfers from other printing surfaces can only be made when the composition used is in the form of a pigment, and reduced to a convenient working consistency.

These, then, comprise the varieties of transfer mediums which are likely to be required in most phases of commercial lithography. Others are, of course, employed for specific purposes and under peculiar conditions; but these, again, are more or less modifications of existing formulae, prepared to meet particular requirements.

The ink used for transferring impressions from one printing surface to another, _e.g._, the re-transferring of work from stone to stone, may with a very slight alteration serve for type to stone transfer; but a considerable departure must be effected to produce a satisfactory photo-litho transfer ink, while a composition of a peculiarly distinctive character will be requisite for the successful production of transfers from copperplate engravings, as well as for a transfer ink for writing and drawing on stone or transfer paper. This writing transfer ink must be soluble in water, yet without becoming slimy; otherwise it will not work freely with the pen or brush. It must also dry quickly, and without any tendency to smear.