Home

The Boy Mechanic Part 52

The Boy Mechanic - novelonlinefull.com

You’re read light novel The Boy Mechanic Part 52 online at NovelOnlineFull.com. Please use the follow button to get notification about the latest chapter next time when you visit NovelOnlineFull.com. Use F11 button to read novel in full-screen(PC only). Drop by anytime you want to read free – fast – latest novel. It’s great if you could leave a comment, share your opinion about the new chapters, new novel with others on the internet. We’ll do our best to bring you the finest, latest novel everyday. Enjoy

The ports were not easy to make, as

[Ill.u.s.tration: The Engine Is About 20 Inches High]

they had to be drilled and chipped out. The steam chest is round, as it had to be made to fit the round tee connection. The crosshead runs in guides made from a piece of gas pipe with the sides cut out and threads cut on both ends. One end is screwed into a rim turned on the cylinder head and the other is fitted into an oblong plate. Both ends of this plate were drilled and tapped to receive 1-1/2-in. pipe.

The main frame consists of one 1-1/2in. pipe 10 in. long and one made up from two pieces of pipe and a cross to make the whole length 10 in. These pipes were then screwed into pipe f.l.a.n.g.es that served as a base. The open part of the cross was babbitted to receive the main shaft. The end of the shaft has a pillow block to take a part of the strain from the main bearing. The eccentric is constructed of washers. While this engine does not give much power, it is easily built, inexpensive, and anyone with a little mechanical ability can make one by closely following out the construction as shown in the ill.u.s.tration.

--Contributed by W. H. Kutscher, Springfield, Ill.

** How to Make a Copper Bowl [185]

To make a copper bowl, such as is shown in the ill.u.s.tration, secure a piece of No. 21 gauge sheet copper of a size sufficient to make a circular disk 6-1/2 in. in diameter.

Cut the copper to the circular form and size just mentioned, and file the edge so that it will be smooth and free from sharp places. With a pencil compa.s.s put on a series of concentric rings about 1/2 in. apart. These are to aid the eye in beating the bowl to form.

The tools are simple and can be made easily. First make a round-nosed mallet of some hard wood, which should have a diameter of about 1-1/4 in, across the head. If nothing better is at hand, saw off a section of a broom handle, round one end and insert a handle into a hole bored in its middle. Next take a block of wood, about 3 by 3 by 6 in., and make in one end a hollow, about 2 in.

across and 1/2 in. deep. Fasten the block solidly, as in a vise, and while holding the copper on the hollowed end of the block, beat with the mallet along the concentric rings.

Begin at the center and work along the rings--giving the copper a circular movement as the beating proceeds--out toward the rim.

Continue the circular movement and work from the rim back toward the center. This operation is to be continued until the bowl has the shape desired, when the bottom is flattened by placing the bowl, bottom side up, on a flat surface and beating the raised part flat. Beating copper tends to harden it and, if continued too long without proper treatment, will cause the metal to break. To overcome this hardness, heat the copper over a bed of coals or a Bunsen burner to a good heat. This process is called annealing, as it softens the metal.

The appearance of a bowl is greatly enhanced by the addition of a border. In the ill.u.s.tration the border design shown was laid out in pencil, a small hole was drilled with a band drill in each s.p.a.ce and a small-bladed metal saw inserted and the part sawed out.

To produce color effects on copper, cover the copper with turpentine and

[Ill.u.s.tration: Shaping the Bowl and Sawing the Lace]

hold over a Bunsen burner until all parts are well heated.

** Cleaning Furniture [185]

After cleaning furniture, the greasy appearance may be removed by adding some good, sharp vinegar to the furniture polish. Vinegar, which is nothing else than diluted acetic acid, is one of the best cleansers of dirty furniture.

** Melting Lead in Tissue Paper [185]

Take a buckshot, wrap it tightly in one thickness of tissue paper, and, holding the ends of the paper in the fingers of each hand, place the part that holds the shot over the flame of a match just far enough away from the flame not to burn the paper. In a few seconds unfold the paper and you will find that the shot has melted without even scorching the paper.

--Contributed by W. O. Hay, Camden, S. C.

** The Principles of the Stereograph [185]

Each of our eyes sees a different picture of any object; the one sees a trifle more to the right-hand side, the other to the left, especially when the object is near to the observer. The stereoscope is the instrument which effects this result by bringing the two pictures together in the senses. The stereograph produces this result in another way than by prisms as in the stereoscope. In the first place there is

[Ill.u.s.tration: Looking Through the Colored Gelatine]

only one picture, not two mounted side by side. The stereograph consists of a piece of card, having therein two circular openings about 1-1/4 in. diameter, at a distance apart corresponding to the distance between the centers of the pupils. The openings are covered with transparent gelatine, the one for the left eye being blue, that for the right, orange. The picture is viewed at a distance of about 7 in. from the stereograph. As a result of looking at it through the stereograph, one sees a colorless black and white picture which stands out from the background. Try looking at the front cover of Popular Mechanics through these colored gelatine openings and the effect will be produced.

If one looks at the picture first with the right eye alone through the orange gla.s.s, and then with the left eye through the blue gla.s.s, one will understand the principle on which the little instrument works. Looking through the blue gla.s.s with the left eye, one sees only those portions which are red on the picture.

But they seem black. The reason is that the red rays are absorbed by the blue filter. Through the orange gelatine all the white portions of the picture seem orange, because of the rays coming from them, and which contain all the colors of the spectrum; only the orange rays may pa.s.s through. The red portions of the picture are not seen, because, although they pa.s.s through the screen, they are not seen against the red ground of the picture. It is just as though they were not there. The left eye therefore sees a black picture on a red background.

In the same way the right eye sees through the orange screen only a black picture on a red background; this black image consisting only of the blue portions of the picture. Any other part of complementary colors than blue and orange, as for instance red and green, would serve the same purpose.

The principle on which the stereograph works may be demonstrated by a very simple experiment. On white paper one makes a picture or mark with a red pencil. Looking at this through a green gla.s.s it appears black on a green ground; looking at it through a red gla.s.s of exactly the same color as the picture, it, however, disappears fully.

Through the gla.s.s one will see only a regular surface of the color of the gla.s.s itself, and without any picture. Through a red gla.s.s a green picture will appear black.

So with the stereograph; each eye sees a black picture representing one of the pictures given by the stereoscope; the only difference being that in the case of the stereograph the background for each eye is colored; while both eyes together see a white background.

In the pictures the red and the green lines and dots must not coincide; neither can they be very far apart in order to produce the desired result. In order that the picture shall be "plastic,"

which increases the sense of depth and shows the effect of distance in the picture, they must be a very trifle apart. The arrangement of the two pictures can be so that one sees the pictures either in front of or on the back of the card on which they are printed. In order to make them appear before the card, the left eye sees through a blue screen, but the red picture which is seen by it is a black one, and lies to the right on the picture; and the right eye sees the lefthand picture. The further apart the pictures are, the further from the card will the composite image appear.

In the manufacture of a stereoscope the difficulty is in the proper arrangement of the prisms; with the stereograph, in the proper choice of colors.

** Mercury Make-and-Break Connections for Induction Coils [187]

Induction coils operating on low voltage have a make-and-break connection called the "buzzer" to increase the secondary discharge. Two types of make-and-break connection are used, the common "buzzer" operated by the magnetism of the core in the coil and the mercury break operated by a small motor. The sketch herewith shows how to make the motor-operated break. Two blocks of wood are nailed together in the shape of an L and a small motor fastened to the top of the vertical piece. The shaft of the motor is bent about 18 in. in the shape of a crank, so that in turning it will describe a circle 1/4 in. in diameter. A small connecting bar is cut from a piece of bra.s.s 1/8 in. thick, 1/4 in. wide and 1 in. long and a hole drilled in each end; one hole to fit the motor shaft and the other to slip on a No. 12 gauge wire. Two L-shaped pieces of bra.s.s are fastened to the side of the block and drilled with holes of such a size that a No. 12 gauge wire will slip through snugly. Place a NO.12 gauge wire in these holes and bend the top end at right angles.

[Ill.u.s.tration: Motor-Driven Make-and-Break]

Put the connecting bra.s.s bar on the motor shaft with washers fitted tight on each side and slip the other end over the bent end of the wire. Have the wire plenty long so it can be cut to the proper length when the parts are all in place. A small round bottle about 1/2 in. in diameter is now fitted in a hole that has been previously bored into the middle of the bottom block and close up to the vertical piece. This should only be bored about half way through the block. The wire is now cut so at the length of the stroke the end will come to about one-half the depth, or the middle of the bottle.

Fill the bottle with mercury to a point so that when the motor is running, the end of the wire will be in the mercury for about one-half of the stroke. Cover the mercury over with a little alcohol. A No. 14 gauge iron wire is bent and put into the side of the bottle with the end extending to the bottom. The other end of this wire is attached to one binding-post placed at the end of the bottom block. The other binding-post is connected to a small bra.s.s brush attached to the side of the vertical piece, which is placed with some pressure on the moving wire. The motor can be run with a current from a separate course or connected as shown on the same batteries with the coil. The proper height of the mercury can be regulated for best results. The motor must run continuous if the coil is used for writing code signals, wireless, etc.

--Contributed by Haraden Pratt, San Francisco, Cal.

** How to Make a Barometer [188]

Atmospheric pressure is measured by the barometer. The weight of the air in round numbers is 15 lb. to the square inch and will support a column of water 1 in. square, 34 ft. high, or a column of mercury (density 13.6) 1 in. square, 30 in. high. The parts necessary to make a simple barometer are, a gla.s.s tube 1/8 in.

internal diameter and about 34 in. long, a bottle 1 in. inside diameter and 2 in. high. Seal one end of the tube by holding it in the flame of a gas burner, which will soon soften the gla.s.s so it can be pinched together with pliers. Put a little paraffin in the bottle and melt it by holding the bottle over a small flame. When cool the paraffin should cover the bottom about 1/16 in. thick.

The tube is now to be filled with mercury. This may be accomplished with a paper funnel, but before attempting to put in the mercury, place a large dish or tray beneath the tube to catch any mercury that may accidentally be spilled. Only redistilled mercury should be used, and the tube should be perfectly clean before filling. When the tube is filled to

[Ill.u.s.tration: Barometer]

within 1 in. of the open end place the forefinger over the hole and tilt the tube up and down so all the air will gather at the finger end. The filling is continued until the tube is full of mercury. The gla.s.s bottle containing the wax covered bottom is now placed over the end of the tube and pressed firmly to insure an airtight fit with the tube. The bottle and tube are inverted and after a few ounces of mercury are put in the bottle the tube may be raised out of the wax, but be careful not to bring its edge above the surface of the mercury.

The instrument is put aside while the base is being made, or, if you choose, have the base ready to receive the parts just described when they are completed. Cut a base from a piece of 7/8-in. pine 3 in. wide and 40 in. long. In this base cut a groove to fit the tube and the s.p.a.ce to be occupied by the bottle is hollowed out with a chisel to a depth of 3/4 in., so the bottle rests on one-half of its diameter above the surface of the board and one-half below. The instrument is made secure to the base with bra.s.s strips tacked on as shown in the sketch. After the instrument is in place put enough mercury in the bottle so the depth of the mercury above the bottom end of the tube will be about 1/2 in.

The scale is made on a piece or cardboard 2 in. wide and 4 in.

long. The 4 in. are marked off and divided into sixteenths, and the inches numbered 27 up to 31. The scale is fastened to the base with glue or tacks and in the position behind the tube as shown in the sketch. Before fastening the scale, the instrument should be compared with a standard barometer and the scale adjusted so both readings are the same. But if a standard barometer is not available, the instrument, if accurately constructed, will calibrate itself.

Please click Like and leave more comments to support and keep us alive.

RECENTLY UPDATED MANGA

Martial Peak

Martial Peak

Martial Peak Chapter 5686: Meng Que Author(s) : Momo,莫默 View : 14,959,333
Emperor’s Domination

Emperor’s Domination

Emperor’s Domination Chapter 5744: Fight To The End Author(s) : Yan Bi Xiao Sheng,厌笔萧生 View : 16,758,091

The Boy Mechanic Part 52 summary

You're reading The Boy Mechanic. This manga has been translated by Updating. Author(s): Popular Mechanics Company. Already has 581 views.

It's great if you read and follow any novel on our website. We promise you that we'll bring you the latest, hottest novel everyday and FREE.

NovelOnlineFull.com is a most smartest website for reading manga online, it can automatic resize images to fit your pc screen, even on your mobile. Experience now by using your smartphone and access to NovelOnlineFull.com