Steel Traps Part 20

CHAPTER x.x.xI.

FROM ANIMAL TO MARKET.

Under this t.i.tle, says an experienced Western trapper, I shall endeavor to show my brother trappers how to handle pelts:

As soon as I get in from my traps (I use a team and wagon), I feed team, dogs and self, then I proceed to skin the game in the usual manner; when game is all skinned I put on my fleshing suit, made of rubber cloth like that buggy curtains are made of, get out my fleshing boards, of which I have three sizes--large, medium and small--for each kind of cased skins except rat, which I flesh with thumb and knife. The fleshing boards are like Fig. 1 on enclosed diagram, made of 1 inch pine free from knots and dressed on both sides, 3 feet 6 inches long, and for skunk 3/4 in. and 10 in. wide, tapered up to a blunt point, edges rounded and sandpapered smooth.

These boards can be made of other sizes so as to fit larger or smaller pelts of other kind.

[Ill.u.s.tration: FLESHING BOARD.]

For a flesher I have tried nearly everything imaginable, dull knives, hardwood sc.r.a.pers, etc., but have abandoned them all for the hatchet.

I use an old lath hatchet head and use it tolerably sharp; I proceed as follows: Put pelt on board but do not fasten, grip lower edge with left hand, pull down hard, place point of board against breast and use hatchet with right, pushing down and holding hatchet nearly flat; use plenty of elbow grease; as fast as you get a strip cleaned off turn hide a little but do not flesh on edge of board. It may not work good at first and you may cut one or two hides, but you will soon get the knack.

[Ill.u.s.tration: STRETCHING FRAME.]

If possible take a b.i.t.c.h skunk for the first as they flesh easier, and be sure there are no burrs or chunks of mud in the fur, or you will cut a hole the size of the burr. Now for the stretchers. In Fig.

2 is what I use; it is something of my own invention, and there is no patent on it. It is made of any wood that will split straight, and the dimensions are as follows: Pieces are 4 ft. long by 1 3/8 in.

dressed smooth; pieces are 1 1/2 X 3/8 in.; will say for large skunks here they would be 10 in. and 4 1/2 in. To frame you must soak or steam the long pieces; mitre the ends and fasten with 3d finishing nails clinched. Then place in position 1 in. from ends and fasten with two 6d finishing nails; place in position and pull up to 8 in.

from nose and fasten: now chamfer off edges and sandpaper smooth.

I like this stretcher, as it airs both sides of pelt and will dry them in half the time. Fig 3 shows manner of fastening pelt; on belly side it can be drawn down and fastened to tail pieces with sack needle and twine; it is made of two or more poles fastened in the shape of a hoop.

In shipping furs, bale tight; do not ship loose in sack; place mink and rat inside of skunk and other fur, and always place the toughest pelts on outside. By bailing tight you will avoid crinkling and they will not look mussy and will bring from 5 to 10 per cent. more. Now, brother trappers, fleshing pelts, as I understand it, is not merely taking the fat off, but in going deeper and taking the flesh clean from the pelt so that if skunk, the stripe will show clear the full length and reducing the weight by half. On February 2nd I shipped 15 skunk, all large; the lot only weighed 9 pounds including sack.

[Ill.u.s.tration: SKIN ON STRETCHER.]

When stretching skunk and otter skins, if the weather is warm, split the tails, open and tack flat. Split open half way all others that have fur tails. Open pelts can be stretched in hoops made of one or more poles an inch or so in diameter, and sewed in with a sack needle and heavy twine.

In stretching do not get the pelt so wide that the fur looks thin, or so long and narrow that it looks as if a horse had been hitched to each end. Keep the natural shape of the animal as much as possible, dry in a cool, airy place inside, or on the north side of a building and away from fire.

Baling--here is where the expert trapper shows his craft, and in baling you will see him wipe off all surplus fat and dirt and place the heavy pelts on the outside of his pack. The lighter furs, such as mink, marten, cat, etc., will be placed inside of the skins that are heavier. For instance: From four to eight rats or mink, inside of a fox or skunk. He will place the head of one to the tail of another, the tails folded in. He now ties a cord tightly around each end, placing them on a square of burlap, and with sack needle and twine draws up the sides as tight as he can; then he folds in the ends and sews up snug. Furs thus packed reach the market in good shape, and not such as they would if crammed promiscuously into a sack.

[Ill.u.s.tration: HOOP STRETCHER.]

In conclusion, boys, let me suggest a maxim or two for your guidance: "Prime caught and well handled furs always bring top prices." "Take pride in your catch, no matter how small."

While the heading of this chapter is "From Animal to Market" it is well when shipping to request the dealer to grade and send value. If satisfactory, write to send on check. If not satisfactory, have dealer return furs.

When shipping furs under these conditions see that no green skins are sent--only properly cured ones.

While some dealers offer to pay expressage both ways we hardly think this fair and if no deal is made the dealer should pay the expressage one way and the shipper the other.

The Hunter-Trader-Trapper, published at Columbus, Ohio, in the interests of hunters, trappers and dealers in raw furs contains a great deal of information that will be of value along the line of shipping furs as well as trapping methods, etc.

CHAPTER x.x.xII.

MISCELLANEOUS INFORMATION.

How to Tan Skins.

I give below several successful receipts for tanning skins and furs of all kinds, but if you have never tanned skins before I would advise you to make your first attempt on some skin of small value, writes an old hunter and trapper. Remove all flesh from a skin before putting thru the tanning process by laying it over what is called a fleshing beam and sc.r.a.ping with a dull knife; the fleshing beam is nothing more than a beam with edges rounded and a log peeled of the bark will answer the purpose very well.

First remove the hair from the hide by putting in 5 gallons of water, 2 gallons of slacked lime, 2 quarts of wood ashes and 3 ounces of soda. After the hair has become loose, try soaking in this mixture, remove it by sc.r.a.ping it off with a stick (be careful not to let it get on the hands, as it is very irritating to the skin). This receipt can be altered according to the number of hides you have to tan. The amount given here is enough for 2 or 3 hides (such as goat, dog and animals of that size.)

Next draw the lime from the skin by putting it in a bath composed of 5 gallons of water, 2 quarts of wheat bran, 4 ounces of acetic acid and 1/2 pound of salt. Finally put the skins in a mixture of 5 gallons of water, 1 pound of salt, 1 1/2 pounds of gambia, and 5 ounces of acetic acid. Leave the skins in each process about three days, take them out often and pull and work them.

When you think the skin is done, take it and put it on a stretcher like a c.o.o.n stretcher, but of course altered to fit the skin you are tanning; stretch the skin tight but not too tight and put in the sun; at intervals of half an hour apply with a brush or rag mixtures number three until the skin will soak up no more.

Do this about three times and then put the skin in the shade or some cool place where there is a free circulation of air to dry. Lastly, when dry, oil flesh side of the skin lightly. This leather if tanned right is the best you can get, but the objections is that a trapper in the woods does not always have a drug store near to purchase the tanning material which is rather expensive, so I will give a few cheap methods also.

The way the Indians tan skins in the woods is to take the brains of the animal and rub the flesh side of the skin with them until it is rubbed in good; they then let them dry, working and pulling them until thoroughly dry. To tan mole, squirrel and such skins, draw the skin over a corn cob or board and place it in the sun, then apply sweet oil every 24 hours. After doing this about five times rub over with fine alum.

To tan for lashes, first remove hair, then put in 1 1/2 handfuls of alum and 3 handfuls of salt in 2 gallons of water; this leather is all right until it gets wet, then it is ruined.

To tan for furs, rub flesh side of the skin with two parts saltpeter and one part alum, roll and let it dry, then work soft. To dry the hair side of skins, take two parts wheat bran and one part clean sand, heat it and rub it in the hair side of skin till dry.

To tan light deer skins and such skins as sheep, dog, etc., put in three quarts of rain water, one ounce of sulphuric acid and a handful of salt; put in the skin, stir around for about five minutes, take it out and work dry, then it can be smoked and is ready for use. I think that by following the above directions closely you can tan any skin that can be tanned.

Camps and How To Build Them.

The trapper who spends the entire trapping season far from civilization must know how to make a comfortable camp or he is likely to pay dearly for his lack of knowledge. Especially is this the case if his trapping is done in the far North where the winters are long and severe.

[Ill.u.s.tration: THE HOME SHANTY.]

The trapper should have one good "home shanty" to be used as a base of supplies for storing furs, etc. He should also have small camps located along his lines at convenient distances so that he can spend the night with some comfort if he has gone too far to return to the home camp.

The home camp is generally a substantial log shack. It should be located in a sheltered spot, if possible, on some little knoll or slightly elevated spot of ground and as close to good fire wood and good drinking water as possible. The proper size of camp depends on the number of persons in the party. A shanty 10 x 12 feet inside is large enough for two persons. If it is larger it will be harder to keep warm. For a camp of this size the logs should be cut 12 and 14 feet long so as to allow for the notching of the corners. Of course the logs should be straight and they should be as near the same thickness as possible.

Having selected a spot for the camp and cleaned away the brush, etc., commence by laying two of the 14 foot logs parallel with each other and about ten feet apart. Cut notches in the ends of these logs, cutting down about half the thickness of the logs and lay two of the 12 foot logs in the notches. The next step is the floor which should be made of straight poles about five or six inches thick and 11 or 12 feet long. They should be fitted down solidly on the two long logs and may be flattened on top with an axe, or with an adz after the camp is finished. Then fit in two more 14 foot logs which will hold the floor poles down solid.

The door frame or boxing should be cut off square at the ends and b.u.t.ted up against the door frame and held there by driving spikes thru the frame into the logs. Use all the large logs on one side so as to be ready for the roof. The simplest, as well as one of the best, kind of roofs is made of poles, c.h.i.n.ked with moss and covered with tar paper or birch bark. The bark roof is the most lasting but requires more work. The door may be made of split cedar, or, if cedar is not to be found, it may be hewn out of almost any kind of wood.

For windows, a couple of small panes of gla.s.s may be fitted in openings, cut between the logs, and all the cracks should be c.h.i.n.ked with moss to make it warm.

There are a number of good stoves in the market, but I prefer to make my own stoves. A good stove may be made of sheet iron by bending it so as to form the top and two sides, riveting an end in behind and hinging a door in front. It has no bottom, being set in a box of earth, but be sure that there is enough dirt or it will burn thru into the floor. Holes should be cut in top for pipe and cooking pots and strips of hoop iron should be riveted on inside to stiffen top.

For stopping camps along the trap lines, the Indian tepee or wigwam is as good as any. They may be made of birch bark or tar paper and if they are covered thickly with boughs and banked with snow it will only require a small fire to keep them warm. If you are fortunate enough to possess a rabbit skin blanket such as are made by the Chippewa Indians you will not need to keep a fire at night.

Trappers Shelter.

I noticed under the head of Short Letters in January number of H-T-T where one Bacellus of New York wishes to know something more about camps in the woods, or how to keep dry and warm in cold and wet weather, writes a Michigan trapper. This is how I build a camp along a trapper's trail:

[Ill.u.s.tration: A LINE SHANTY.]

I cut the logs about 9 feet long, cut them small enough so one man would be able to handle them. If cut from dry cedar or other light wood, they can be of good size. I lay the logs up on three sides until the walls are about 5 1/2 feet high, then I procure two stakes about 8 or 9 feet long with a crotch on one end; the other end I sharpen so it can be driven in the ground outside the open end of the camp. There are also two shorter stakes placed inside of the camp just opposite the outside ones and tied together at top with a withe, wire or piece of rope--these stakes are intended to hold the ends of the logs together, and also act as a support for the roof, which is made shanty fashion. I next place a pole about 5 inches thick by 10 feet long across from one crotched stake to the other. Now from the back wall to the top hole I place scoops made out of split logs hollowed out with axe. They are placed split side up and another scoop placed over the first two. Short pieces of logs are put in under the last outside scoops and every crack is mossed up tight, and a bunk placed across the end about a foot from the ground, and fire built in the center of open side. By placing 2 crotched stakes in the ground like the first pair about 5 feet from them, and placing a pole across the tops and then two short brace pieces between these two top poles. After this, straight poles ten feet long, about what one man can handle, are taken and placed all around the outside or open end of camp. This prevents the smoke from whirling 'round the camp, and it goes up straight.