Mission Furniture Volume I Part 10

1 seat, 1 by 16 by 35-3/4 in., S-4-S.

2 top end braces, 3/4 by 2 by 14-1/2 in., S-4-S.

6 slats, 3/4 by 2 by 6-1/2 in., S-4-S.

Square up the four posts and lay out the mortises according to the drawing. To do this, lay them on a flat surface with the ends square and mark them with a try-square. The tenons on the end and side rails are laid out in the same manner as the posts. The end rails should be marked and mortises cut for the upright slats as shown in the detail drawing.

Fit the end and side braces with mortise and tenon joints.

The two end frames can now be glued and clamped together and set away to dry. Put all the parts together before gluing to see that they fit square and tight.

The seat should be made of one piece if possible, otherwise two or more boards will have to be glued together. The corners should be cut out to fit around the posts. It rests on the side rails and cleats fastened to the inner side of the end rails.

When the window seat is complete go over it carefully and sc.r.a.pe all the surplus glue from about the joints, as the finish will not take where there is any glue. Remove all rough spots with fine sandpaper, then apply the stain best liked, which may be any one of the many mission stains supplied by the trade for this purpose. If this window seat is well made and finished, it will be an ornament to any home.

[Ill.u.s.tration: Detail of the Hall or Window Seat]

A MISSION PLANT STAND

For the mission plant stand shown in the ill.u.s.tration secure the following list of quarter-sawed white-oak stock, cut and finished to size:

1 top, 3/4 by 15-1/2 by 15-1/2 in., S-2-S.

4 posts, 1-1/4 by 1-1/4 by 20 in., S-4-S.

4 rails, 3/4 by 3 by 11 in., S-2-S.

2 rails, 3/4 by 2 by 11 in., S-2-S.

1 shelf, 3/4 by 6 by 10 in., S-2-S.

4 slats, 1/4 by 2 by 12-1/4 in., S-2-S.

2 slats, 1/4 by 2 by 12-3/4 in., S-2-S.

Test all surfaces of the posts with a try-square to see that they are square with each other. Lay out the tenons on the ends of the rails as shown in the sketch and cut with a tenon saw and chisel. Arrange the posts and rails as they are to stand and number each tenon and mortise.

Lay out the mortises in the legs, taking the measurements directly from the tenon which is to fit that mortise. Cut the mortises, first having bored to the depth with a 1/4-in. bit.

[Ill.u.s.tration: Detail of the Plant Stand]

The slats should now be made and mortised into the top rail 1/4 in. They come outside of the lower rail and are held to it with two small brads, fancy-headed tacks, or round-head screws.

In laying out the mortises for the lower rails, care must be taken to have them set 1/8 in. farther in than the upper rails so the slats may come outside.

Set up the stand without glue or screws to see that all pieces fit accurately. Then glue up the sides with the slats first. After these have set for 24 hours, fit in the other two rails and the shelf. Three flat-head screws should be used to hold the shelf in place. These must be placed so the slats will cover them when they are attached.

[Ill.u.s.tration: Complete Plant Stand]

When this work is completed it is ready for the top. A good method of attaching the top is shown in the sketch. The screws used for fastening should be 2-in. No. 10. Bore into the rail 1-1/2 in. with a bit 1/16 in.

larger than the head of the screw. Then bore through the rest of the way with a bit a little larger than the shank of the screw. Thus a little s.p.a.ce is left for expansion and shrinkage of the top.

Sc.r.a.pe and sandpaper thoroughly to remove all marks or glue spots.

Finish with two coats of weathered-oak stain, followed by two coats of black wax.

A BEDSIDE MEDICINE STAND

The accompanying sketch and detail drawing show a design of a bedside stand. This is a very desirable piece of furniture and is simple and easy to make. Quarter-sawed oak is the best wood to use in its construction. The material should be ordered from the mill ready cut to length, squared and sanded. The following list of material will be required:

4 posts, 1-3/4 by 1-3/4 by 33 in., S-4-S.

1 top board, 1 by 19 by 19 in., S-4-S.

3 intermediate boards, 3/4 by 15-1/2 by 17 in., S-4-S.

2 side boards, 3/4 by 5 by 15-1/2 in., S-4-S.

1 back board, 3/4 by 4-1/4 by 14-1/2 in., S-4-S.

4 side rails, 3/4 by 2 by 16 in., S-4-S.

1 door, 3/4 by 9 by 14-1/2 in., S-4-S.

1 back board, 3/4 by 10-1/4 by 14-1/2 in., S-4-S.

2 panels, 3/8 by 9-1/2 by 15 in., S-4-S.

6 slats, 1/4 by 1 by 8-3/4 in., S-4-S.

1 drawer front, 3/4 by 4-1/4 by 14-1/2 in., S-4-S.

2 sides for drawer, 1/2 by 4-1/4 by 16 in., S-4-S.

1 back for drawer, 1/2 by 4-1/4 by 13-1/2 in., soft wood.

1 bottom for drawer, 1/2 by 13-1/2 by 15 in., soft wood.

[Ill.u.s.tration: Medicine Stand in Quarter-Sawed Oak]

Start work on the four posts by rounding the top corners and shaping the feet as shown. The four posts are identical and the mortises should be laid out on all four at once so as to get them all alike. These should be carefully cut with a sharp chisel. On the inner surface of each leg cut a groove to hold the side boards of the lower compartment. Next prepare the two wide and the four narrow crosspieces, tenoning them to fit the mortises already cut in the legs. The lower crosspieces should also have grooves cut in them to hold the side boards of the compartment. The two complete sides can now be glued and clamped together and set away to dry. While they are drying the remaining parts of the stand can be made. The three horizontal boards are now made by notching out the corners to fit around the legs. They are supported by fastening small cleats to the inner surface of each crosspiece.

[Ill.u.s.tration: Detail of the Medicine Stand]

The two ends can now be set up and connected. Notch out the corners of the top board and fit it in place. The top is fastened down by means of screws set in at an angle from below. The back boards can be of soft wood and are fastened in place in the usual manner. The door should be of one piece if possible and should have suitable hinges and a catch.

Make and fit the drawer in place, and the stand is ready for the finish.

First sc.r.a.pe all the surplus glue from about the points so the stain will not be kept from the wood. Finish smooth with fine sandpaper, then apply stain of the color desired.

A MISSION HALL CHAIR

This hall chair is designed to take up as little room as possible. For its construction the following stock will be needed:

1 back, 7/8 by 14 by 44 in., S-2-S.

2 sides, 7/8 by 14 by 17 in., S-2-S.

1 seat, 7/8 by 14 by 14 in., S-2-S.

1 stretcher, 7/8 by 6 by 16 in., S-2-S.

1 brace, 7/8 by 5 by 11 in., S-2-S.

1 piece, 7/8 by 7/8 by 44 in., for cleats.

These dimensions are for finished pieces, therefore 1/4 in. should be allowed for planing if the stock cannot be secured finished.