Electricity for the 4-H Scientist Part 5

4. Tie the holding knot (underwriters' knot) as explained in Step 5.

5. Connect wires to terminal screws and a.s.semble the rubber-handled socket.

6. Screw in the rough service lamp and test your cord.

7. Put the shielded lamp guard on the socket and tighten the holding clamp until it is firmly in place. You are now ready to use or demonstrate your trouble light.

8. After you've made your trouble light, decide on a good place to keep it where it will be handy for use. Loop it carefully and hang it over a wooden dowel rather than a nail. It will last longer.

[Ill.u.s.tration: Figure 1 Tying an Underwriter's Knot]

[Ill.u.s.tration: Figure 2 Disa.s.sembled Light]

What Did You Learn?

(Underline correct answer)

1. A Junior Hard Service Cord is known as an (SO-Type) (SJO-Type) cord.

2. You disconnect a cord by (jerking it from the socket) (grasping plug and pulling it out).

3. Bra.s.s sockets are unsafe because (they break too easily) (the exposed metal can cause short circuits).

4. Rubber-covered cord is safer for emergency cords than fabric because (it will stretch) (it will insulate and protect the wires inside).

5. In a trouble light (any kind of bulb will do) (a rough service bulb is best).

Ideas for Demonstrations and Exhibits

1. Show how to make your trouble light and a method of storing it.

2. Show a safe trouble light, and an unsafe trouble light with danger points marked.

3. Show cutaway pieces of different types of cord.

For More Information

Ask your power supplier, county highway engineer, police official or leader to tell you about various types of portable emergency lights and their uses.

LESSON NO. B-5

Credit Points 5

WHAT MAKES MOTORS RUN

What makes an electric motor run? Can you make an electric motor that will run? Certainly you can, and by doing so you'll learn why it runs.

It won't be mysterious any more and you'll be ahead of all the millions of people who use motors every day and never know why or how the motor converts electrical energy into useful power.

[Ill.u.s.tration]

Motors Are Magnets

You know how one end of a compa.s.s needle always points to North. No matter how you turn the compa.s.s, the same end of the needle always swings to the North. The earth itself and that small compa.s.s are both magnets (Figure 1). Each has a North pole and a South pole. Around the poles of each there are magnetic fields, invisible lines of force that attract and repel.

[Ill.u.s.tration: Figure 1. The same end of the compa.s.s needle always points to the earth's magnetic North Pole.]

The N poles _repel_ each other and so do the S poles. The N and S poles _attract_ each other. In other words, opposite poles attract; poles that are alike repel each other.

Lay 2 bar magnets on a table side-by-side. If both N poles are at one end, they'll repel each other and almost flip around until there's a N pole lying next to a S pole (Figure 2).

[Ill.u.s.tration: Figure 2. Small bar magnets laid side by side move so that the North pole of one is near the South pole of the other.]

Now suppose we place one of the bar magnets on the table. The other, we'll fix on a pivot so it can spin around. This one we'll move so its N pole almost touches the fixed magnet's N pole. As soon as we release it, the movable magnet will spin around so its S pole will be near the N pole of the stationary magnet. That's an electric motor--almost.

[Ill.u.s.tration: Figure 3. A movable bar magnet pivots so its South pole is near the North pole of a stationary magnet.]

It's not quite a motor because the rotating magnet will just move as far as it has to in order to get the opposite poles together. You might be able to cause the movable bar magnet to make turn after turn. You could do this by turning the fixed magnet quickly end for end. This wouldn't be very practical as a motor.

We Can Improve It

If we could change the pole on one end of the rotating magnet just as soon as it reaches the attracting pole, it could make a complete circle.

In doing that, the pole at the near end of the rotating magnet would be repelled by the stationary magnet and pushed away. As soon as the opposite end of the rotating magnet would come into the magnetic field, it would be drawn to the stationary magnet. In order to keep the "motor"

running, we would have to constantly change the poles at each end on every half revolution.

We Need An Electromagnet

We can't reverse the poles on simple bar magnets, but we can on _electromagnets_. We can make one by wrapping a wire several times around an iron core to form a coil. This magnet will also have a N and a S pole when connected to electrical current. The big difference is that the poles can be changed instantly by reversing the current in the wire.

Switching Poles Automatically

The rotating electromagnet will have to be connected to the 2 wires through which we pa.s.s the current. Since it's rotating on a center shaft, we can't have a solid connection. Instead we have to extend the wires from the coil out along the shaft and let the electric contact be made with brushes which touch the wires along the shaft.

[Ill.u.s.tration: Figure 4. A rotating electromagnet changes poles as contacts are made first one way, then the other.]

This is a simple way to reverse the current in the coil of the electromagnet.

Increasing Efficiency