Arts and Crafts in the Middle Ages Part 6

It helps one to understand the differences and similarities in enamelled work, to observe the three general forms in which it is employed; these are, the cloisonne, the champleve, and the painted enamel. There are many subdivisions of these cla.s.sifications, but for our purpose these three will suffice.

In cloisonne, the only manner known to the Greek, Anglo-Saxon, and Celtic craftsmen, the pattern is made upon a gold ground, by little upright wire lines, like filigree, the enamel is fused into all the little compartments thus formed, each bit being one clear colour, on the principle of a mosaic. The colours were always rather clear and crude, but are the more sincere and decorative on this account, the worker recognizing frankly the limitation of the material; and the gold outline harmonizes the whole, as it does in any form of art work. A cloisonne enamel is practically a mosaic, in which the separations consist of narrow bands of metal instead of plaster.

The enamel was applied in its powdered state on the gold, and then fused all together in the furnace.

[Ill.u.s.tration: GERMAN ENAMEL, 13TH CENTURY]

Champleve enamel has somewhat the same effect as the cloisonne, but the end is attained by different means. The outline is left in metal, and the whole background is cut away and sunk, thus making the hollow chambers for the vitreous paste, in one piece, instead of by means of wires. Often it is not easy to determine which method has been employed to produce a given work.

Painted enamels were not employed in the earliest times, but came to perfection in the Renaissance. A translucent enamel prevailed especially in Italy: a low relief was made with the graver on gold or silver; fine raised lines were left here and there, to separate the colours. Therefore, where the cutting was deepest, the enamel ran thicker, and consequently darker in colour, giving the effect of shading, while in reality only one tint had been used. The powdered and moistened enamel was spread evenly with a spatula over the whole surface, and allowed to stand in the kiln until it liquefied.

Another form of enamel was used to colour gold work in relief, with a permanent coating of transparent colour. Sometimes this colour was applied in several coats, one upon another, and the features painted with a later touch. Much enamelled jewelry was made in this way, figures, dragons, and animal forms, being among the most familiar. But an actual enamel painting--on the principle of a picture, was rendered in still another way. In preparing the ground for enamel painting, there are two things which have been essentially considered in all times and countries. The enamel ground must be more fusible than the metal on which it is placed, or else both would melt together. Also the enamel with which the final decoration is executed must be more easily made fluid than the harder enamel on which it is laid. In fact, each coat must of necessity be a trifle more fusible than the preceding one. A very accurate knowledge is necessary to execute such a work, as will be readily understood.

[Ill.u.s.tration: ENAMELLED GOLD BOOK COVER, SIENA]

In examining historic examples of enamel, the curious oval set in gold, known as the Alfred Jewel, is among the first which come within our province. It was found in Somersetshire, and probably dates from about the year 878. It consists of an enamelled figure covered by a thick crystal, set in filigree, around the edge of which runs the inscription, "AELFRED MEC REHT GAVUR CAN" (Alfred ordered me to be wrought). King Alfred was a great patron of the arts. Of such Anglo-Saxon work, an ancient poem in the Exeter Book testifies:

"For one a wondrous skill in goldsmith's art is provided Full oft he decorates and well adorns A powerful king's n.o.bles."

Celtic enamels are interesting, being usually set in the s.p.a.ces among the rambling interlaces of this school of goldsmithing. The Cross of Cong is among the most famous specimens of this work, and also the bosses on the Ardagh Chalice.

The monk Theophilus describes the process of enamelling in a graphic manner. He directs his workmen to "adapt their pieces of gold in all the settings in which the gla.s.s gems are to be placed" (by which we see that he teaches the cloisonne method). "Cut small bands of exceedingly thin gold," he continues, "in which you will bend and fashion whatever work you wish to make in enamel, whether circles, knots, or small flowers, or birds, or animals, or figures." He then admonishes one to solder it with greatest care, two or three times, until all the pieces adhere firmly to the plate. To prepare the powdered gla.s.s, Theophilus advises placing a piece of gla.s.s in the fire, and, when it has become glowing, "throw it into a copper vessel in which there is water, and it instantly flies into small fragments which you break with a round pestle until quite fine. The next step is to put the powder in its destined cloison, and to place the whole jewel upon a thin piece of iron, over which fits a cover to protect the enamel from the coals, and put it in the most intensely hot part of the fire." Theophilus recommends that this little iron cover be "perforated finely all over so that the holes may be inside flat and wide, and outside finer and rough, in order to stop the cinders if by chance they should fall upon it." This process of firing may have to be repeated several times, until the enamel fills every s.p.a.ce evenly. Then follows the tedious task of burnishing; setting the jewel in a strong bit of wax, you are told to rub it on a "smooth hard bone," until it is polished well and evenly.

Benvenuto Cellini recommends a little paper sponge to be used in smoothing the face of enamels. "Take a clean nice piece of paper," he writes, "and chew it well between your teeth,--that is, if you have got any--I could not do it, because I've none left!"

A celebrated piece of goldsmith's work of the tenth century is the Pala d'Oro at St. Mark's in Venice. This is a gold altar piece or reredos, about eleven feet long and seven feet high, richly wrought in the Byzantine style, and set with enamels and precious stones. The peculiar quality of the surface of the gold still lingers in the memory; it looks almost liquid, and suggests the appearance of metal in a fluid state. On its wonderful divisions and arched compartments are no less than twelve hundred pearls, and twelve hundred other precious gems. These stones surround the openings in which are placed the very beautiful enamel figures of saints and sacred personages. St. Michael occupies a prominent position; the figure is partly in relief. The largest medallion contains the figure of Christ in glory, and in other compartments may be seen even such secular personages as the Empress Irene, and the Doge who was ruling Venice at the time this altar piece was put in place--the year 1106. The Pala d'Oro is worked in the champleve process, the ground having been cut away to receive the melted enamel. It is undoubtedly a Byzantine work; the Doge Orseolo, in 976, ordered it to be made by the enamellers of Constantinople.

It was not finished for nearly two centuries, arriving in Venice in 1102, when the portrait of the Doge then reigning was added to it. The Byzantine range of colours was copious; they had white, two reds, bright and dark, dark and light blue, green, violet, yellow, flesh tint, and black. These tints were always fused separately, one in each cloison: the Greeks in this period never tried to blend colours, and more than one tint never appears in a compartment. The enlarging and improving of the Pam d'Oro was carried on by Greek artists in Venice in 1105. It was twice altered after that, once in the fourteenth century for Dandolo, and thus the pure Byzantine type is somewhat invaded by the Gothic spirit. The restorations in 1345 were presided over by Gianmaria Boninsegna.

One of the most noted specimens of enamel work is on the Crown of Charlemagne,[1] which is a magnificent structure of eight plaques of gold, joined by hinges, and surmounted by a cross in the front, and an arch crossing the whole like a rib from back to front. The other cross rib has been lost, but originally the crown was arched by two ribs at the top. The plates of gold are ornamented, one with jewels, and filigree, and the next with a large figure in enamel. These figures are similar to those occurring on the Pala d'Oro.

[Footnote 1: See Fig. 1.]

[Ill.u.s.tration: DETAIL; SHRINE OF THE THREE KINGS, COLOGNE]

The Shrine of the Three Kings in Cologne is decorated both with cloisonne and champleve enamels,--an unusual circ.u.mstance. In Aix la Chapelle the shrine of Charlemagne is extremely like it in some respects, but the only enamels are in champleve. Good examples of translucent enamels in relief may be seen on several of the reliquaries at Aix la Chapelle.

Theophilus gives us directions for making a very ornate chalice with handles, richly embossed and ornamented with mello. Another paragraph instructs us how to make a golden chalice decorated with precious stones and pearls. It would be interesting as a modern problem, to follow minutely his directions, and to build the actual chalice described in the eleventh century. To apply the gems and pearls Theophilus directs us to "cut pieces like straps," which you "bend together to make small settings of them, by which the stones may be enclosed." These little settings, with their stones, are to be fixed with flour paste in their places and then warmed over the coals until they adhere. This sounds a little risky, but we fancy he must have succeeded, and, indeed, it seems to have been the usual way of setting stones in the early centuries. Filigree flowers are then to be added, and the whole soldered into place in a most primitive manner, banking the coals in the shape of a small furnace, so that the coals may lie thickly around the circ.u.mference, and when the solder "flows about as if undulating," the artist is to sprinkle it quickly with water, and take it out of the fire.

Niello, with which the chalice of Theophilus is also to be enriched, stands in relation to the more beautiful art of enamel, as drawing does to painting, and it is well to consider it here. Both the Romans and the Anglo-Saxons understood its use. It has been employed as an art ever since the sixth and seventh centuries. The term "niello" probably is an abbreviation of the Italian word "nigellus"

(black); the art is that of inlaying an engraved surface with a black paste, which is thoroughly durable and hard as the metal itself in most cases, the only difference being in flexibility; if the metal plate is bent, the niello will crack and flake off.

[Ill.u.s.tration: FINIGUERRA'S PAX, FLORENCE]

Niello is more than simply a drawing on metal. That would come under the head of engraving. A graver is used to cut out the design on the surface of the silver, which is simply a polished plane. When the drawing has been thus incised, a black enamel, made of lead, lamp black, and other substances, is filled into the interstices, and rubbed in; when quite dry and hard, this is polished. The result is a black enamel which is then fused into the silver, so that the whole is one surface, and the decoration becomes part of the original plate. The process as described by Theophilus is as follows: "Compose the niello in this manner; take pure silver and divide it into equal parts, adding to it a third part of pure copper, and taking yellow sulphur, break it very small... and when you have liquefied the silver with the copper, stir it evenly with charcoal, and instantly pour into it lead and sulphur." This niello paste is then made into a stick, and heated until "it glows: then with another forceps, long and thin, hold the niello and rub it all over the places which you wish to make black, until the drawing be full, and carrying it away from the fire, make it smooth with a flat file, until the silver appear." When Theophilus has finished his directions, he adds: "And take great care that no further work is required." To polish the niello, he directs us to "pumice it with a damp stone, until it is made everywhere bright."

There are various accounts of how Finiguerra, who was a worker in niello in Florence, discovered by its means the art of steel engraving. It is probably only a legendary narrative, but it is always told as one of the apocryphal stories when the origin of printing is discussed, and may not be out of place here. Maso Finiguerra, a Florentine, had just engraved the plate for his famous niello, a Pax which is now to be seen in the Bargello, and had filled it in with the fluid enamel, which was standing waiting until it should be dry. Then, according to some authorities, a piece of paper blew upon the damp surface, on which, after carefully removing it, Maso found his design was impressed; others state that it was through the servant's laying a damp cloth upon it, that the principle of printing from an incised plate was suggested.

At any rate, Finiguerra took the hint, it is said, and made an impression on paper, rolling it, as one would do with an etching or engraving.

In the Silver Chamber in the Pitti Palace is a Pax, by Mantegna, made in the same way as that by Finiguerra, and bearing comparison with it. The engraving is most delicate, and it is difficult to imagine a better specimen of the art. The Madonna and Child, seated in an arbour, occupy the centre of the composition, which is framed with jewelled bands, the frame being divided into sixteen compartments, in each of which is seen a tiny and exquisite picture.

The work on the arbour of roses in which the Virgin sits is of remarkable quality, as well as the small birds and animals introduced into the composition. In the background, St. Christopher is seen crossing the river with the Christ Child on his back, while in the water a fish and a swan are visible.

In Valencia in Spain may be seen a chalice which has been supposed to be the very cup in which Our Saviour inst.i.tuted the Communion.

The cup itself is of sardonyx, and of fine form. The base is made of the same stone, and handles and bands are of gold, adorned with black enamel. Pearls, rubies, sapphires, and emeralds are set in profusion about the stem and base. It is a work of the epoch of Imperial Rome.

In England, one of the most perfect specimens of fine, close work, is the Wilton Chalice, dating from the twelfth century. The Warwick Bowl, too, is of very delicate workmanship, and both are covered with minute scenes and figures. One of the most splendid treasures in this line is the crozier of William Wyckham, now in Oxford.

It is strictly national in style.

The agreement entered into between Henry VII., and Abbot Islip, for the building of the chapel of that king in Westminster, is extant. It is bound in velvet and bossed with enamels. It is an interesting fact that some of the enamels are in the Italian style, while others are evidently English.

Limoges was the most famous centre of the art of enamelling in the twelfth century, the work being known as Opus de Limogia, or Labor Limogiae. Limoges was a Roman settlement, and enamels were made there as early as the time of Philostratus. Champleve enamel, while it was not produced among the Greeks, nor even in Byzantine work, was almost invariable at Limoges in the earlier days: one can readily tell the difference between a Byzantine enamel and an early Limoges enamel by this test, when there is otherwise sufficient similarity of design to warrant the question.

Some of the most beautiful enamels of Limoges were executed in what was called ba.s.se-taille, or transparent enamel on gold grounds, which had been first prepared in bas-relief. Champleve enamel was often used on copper, for such things as pastoral staves, reliquaries, and larger bits of church furniture. The enamel used on copper is usually opaque, and somewhat coa.r.s.er in texture than that employed on gold or silver. Owing to their additional toughness, these specimens are usually in perfect preservation. In 1327, Guillaume de Harie, in his will, bequeathed 800 francs to make two high tombs, to be covered with Limoges enamel, one for himself, and the other for "Blanche d'Avange, my dear companion."

[Ill.u.s.tration: ITALIAN ENAMELLED CROZIER, 14TH CENTURY]

An interesting form of cloisonne enamel was that known as "plique a jour," which consists of a filigree setting with the enamel in transparent bits, without any metallic background. It is still made in many parts of the world. When held to the light it resembles minute arrangements of stained gla.s.s. Francis I.

showed Benvenuto Cellini a wonderful bowl of this description, and asked Cellini if he could possibly imagine how the result was attained. "Sacred Majesty," replied Benvenuto, "I can tell you exactly how it is done," and he proceeded to explain to the astonished courtiers how the bowl was constructed, bit by bit, inside a bowl of thin iron lined with clay. The wires were fastened in place with glue until the design was complete, and then the enamel was put in place, the whole being fused together at the soldering. The clay form to which all this temporarily adhered was then removed, and the work, transparent and ephemeral, was ready to stand alone.

King John gave to the city of Lynn a magnificent cup of gold, enamelled, with figures of courtiers of the period, engaged in the sports of hawking and hare-hunting, and dressed in the costume of the king's reign. "King John gave to the Corporation a rich cup and cover,"

says Mackarel, "weighing seventy-three ounces, which is preserved to this day and upon all public occasions and entertainments used with some uncommon ceremonies at drinking the health of the King or Queen, and whoever goes to visit the Mayor must drink out of this cup, which contains a full pint." The colours of the enamels which are used as flat values in backgrounds to the little silver figures, are dark rose, clear blue, and soft green. The dresses of the persons are also picked out in the same colours, varied from the grounds. This cup was drawn by John Carter in 1787, he having had much trouble in getting permission to study the original for that purpose! He took letters of introduction to the Corporation, but they appeared to suspect him of some imposture; at first they refused to entertain his proposal at all, but after several applications, he was allowed to have the original before him, in a closed room, in company with a person appointed by them but at his expense, to watch him and see that no harm came to the precious cup!

The translucent enamels on relief were made a great deal by the Italian goldsmiths; Vasari alludes to this cla.s.s of work as "a species of painting united with sculpture."

As enamel came by degrees to be used as if it were paint, one of the chief charms of the art died. The limits of this art were its strength, and simple straight-forward use of the material was its best expression. The method of making a painted enamel was as follows.

The design was laid out with a stilus on a copper plate. Then a flux of plain enamel was fused on to the surface, all over it. The drawing was then made again, on the same lines, in a dark medium, and the colours were laid flat inside the dark lines, accepting these lines as if they had been wires around cloisons. All painted enamels had to be enamelled on the back as well, to prevent warping in the furnace when the shrinkage took place. After each layer of colour the whole plate was fired. In the fifteenth century these enamels were popular and retained some semblance of respect for the limitation of material; later, greater facility led, as it does in most of the arts, to a decadence in taste, and florid pictures, with as many colours and shadows as would appear in an oil painting, resulted. Here and there, where special metallic brilliancy was desired, a leaf of gold was laid under the colour of some transparent enamel, giving a decorative l.u.s.tre. These bits of brilliant metal were known as _paillons_.

When Limoges had finally become the royal manufactory of enamels, under Francis I., the head of the works was Leonard Limousin, created "Valet de Chambre du Roi," to show his sovereign's appreciation.

Remarkable examples of the work of Leonard Limousin, executed in 1547, are the large figures of the Apostles to be seen in the church of St. Pierre, at Chartres, where they are ranged about the apsidal chapel. They are painted enamels on copper sheets twenty-four by eleven inches, and are in a wonderful state of preservation. They were the gift of Henri II. to Diane de Poictiers and were brought to Chartres from the Chateau d'Anet. These enamels, being on a white ground, have something the effect of paintings in Faience; the colouring is delicate, and they have occasional gold touches.

A treatise by William of Ess.e.x directs the artist how to prepare a plate for a painted enamel, such as were used in miniature work.

He says "To make a plate for the artist to paint upon: a piece of gold or copper being chosen, of requisite dimensions, and varying from about 1/18 to 1/16 of an inch in thickness, is covered with pulverized enamel, and pa.s.sed through the fire, until it becomes of a white heat; another coating of enamel is then added, and the plate again fired; afterwards a thin layer of a substance called flux is laid upon the surface of the enamel, and the plate undergoes the action of heat for a third time. It is now ready for the painter to commence his picture upon."

Leonard Limousin painted from 1532 until 1574. He used the process as described by William of Ess.e.x (which afterwards became very popular for miniaturists), and also composed veritable pictures of his own design. It is out of our province to trace the history of the Limoges enamellers after this period.

CHAPTER IV

OTHER METALS

The "perils that environ men that meddle with cold iron" are many; but those who attempt to control hot iron are also to be respected, when they achieve an artistic result with this unsympathetic metal, which by nature is entirely lacking in charm, in colour and texture, and depends more upon a proper application of design than any other, in order to overcome the obstacles to beauty with which it is beset.

"Rust hath corrupted," unfortunately, many interesting antiquities in iron, so that only a limited number of specimens of this metal have come down to us from very early times; one of the earliest in England is a grave-stone of cast metal, of the date 1350: it is decorated with a cross, and has the epitaph, "Pray for the soul of Joan Collins."

The process of casting iron was as follows. The moulds were made of a sandy substance, composed of a mixture of brick dust, loam, plaster, and charcoal. A bed of this sand was made, and into it was pressed a wooden or metal pattern. When this was removed, the imprint remained in the sand. Liquid metal was run into the mould so formed, and would cool into the desired shape. As with a plaster cast, it was necessary to employ two such beds, the sand being firmly held in boxes, if the object was to be rounded, and then the two halves thus made were put together. Flat objects, such as fire-backs, could be run into a single mould.

Bartholomew, in his book "On the Properties of Things," makes certain statements about iron which are interesting: "Though iron cometh of the earth, yet it is most hard and sad, and therefore with beating and smiting it suppresseth and dilateth all other metal, and maketh it stretch on length and on breadth." This is the key-note to the work of a blacksmith: it is what he has done from the first, and is still doing.

In Spain there have been iron mines ever since the days when Pliny wrote and alluded to them, but there are few samples in that country to lead us to regard it as aesthetic in its purpose until the fifteenth century.